Application Guide: Power Trowel on Commercial Jobs.

Same-Day Application, No Scrubbing, No Stripping.

To get a cure, hardener, and densifer just apply Protec III: Original at 400 square feet per US gallon/9.8 litres per square meter (Estimated cost: 5¢ per square foot/54¢ per square meter) across the entire surface once finishing is complete.

No scrubbing, cleanup, or sealing then removing a sealer is needed to cure, harden, and dust-proof your surface with Protec III: Original.

After applying spread out any puddles about every 10 minutes until the majority of product has absorbed.


Dust-proof and Densify Your Flatwork Floors.

To dust-proof and add extra strength, just apply the product after cleaning saw cuts at 400 square feet per US gallon/9.8 litres per square meter (Estimated cost: 5¢ per square foot/54¢ per square meter), at this point do as many additional coats as desired, allowing all product to absorb and dry completely before applying more.

After applying spread out any puddles about every 10 minutes until the majority of product has absorbed. Your shop floor will be ready to use as soon as the product has absorbed.

Because Protec III: Original is non-membrane forming you only need to vacuum up the saw cut dust before applying any additional coats, no washing is required.

The concrete should become dust-proof after enough traffic has polished the floor, or after burnishing the surface to create the permanent shine immediately.

Application Guide: Power Trowel Finished Precast.

Your Product for Efflorescence, Curing, and Improved Finishing.

To get a finishing aid and cure in one step just apply Protec III: Original at 350 square feet per US gallon/8.6 liters per square meter (Estimated cost: 5.7¢ per square foot/62¢ per square meter) after screeding, then proceed to finish as normal.

Streamlining your manufacturing by getting your topical cure, improved surface finishing, and efflorescence prevention in a single-step process is what you get with Protec III: Original.

Protec III: Original replaces water curing, and you do not need change any of your existing processes, because the concrete will be effectively left natural for later painting.


Solve Your Problems with Chemistry.

Prevent efflorescence and carbonation by chemically neutralizing the water-soluble calcium within your concrete surfaces.

Apply either during normal finishing, after removing from your mould, or both.

Application Guide: Power Trowel on Residential Jobs.

Finish In Difficult Conditions, Get a Flatter Surface, Cure, and Dust-proof Your Flatwork.

Applying Protec III: Original on normal power trowel concrete is as natural as it gets.

Simply apply the product with a sprayer at 300 square feet per US gallon/7.4 litres per square meter (Estimated cost: 6.7¢ per square foot/72¢ per square meter) across the entire surface after screeding. For larger pours, apply after you screed each section.

Once applied, immediately work all product in with 2-3 passes of your concrete float.

Give fast-drying areas a light spray, then fully work all product in.


Dustproof And Densify With Another Coat After Saw Cuts.

With Protec III: Original being a water-based and non-membrane forming product you do not need to wash the concrete after saw cuts before applying a second coat.

To apply a second coat for dust-proofing and extra hardness, simply apply the product after saw cuts at 400 square feet per US gallon/9.8 litres per square meter (Estimated cost: 5¢ per square foot/54¢ per square meter) after removing most saw dust, do as many coats as desired, allowing all product to absorb and dry completely before applying more.

Your shop floor will be ready to walk on as soon as the product has absorbed.

Application Guide: Polished Concrete.

Rinse Free, Ready-To-Use Densifier and Polishing Aid.

After cleaning the floor begin polishing with a 200 grit resin polishing pad, once you're done polishing clean the floor again, then apply Protec III: Original at 160 square feet per US gallon/3.9 liters per square meter (Estimated cost: 12.5¢ per square foot/1.35¢ per square meter).

Ensure that the floor remains wet for 20 minutes, spread product around to more absorbent areas every 10 minutes. Apply more product on fast-drying areas.

After all product has fully dried, equip blue nylon pads or diamond impregnated pads then buff the surface until you achieve your desired shine.


Use The Same Product for Ultra-high Shine Polishing Jobs.

Protec III Original can also be used to achieve higher shines for more premium floors. After completing your starting polish with your 200 grit resin polishing pads, equip your 400 grit resin polishing pads.

Apply a light amount of Protec III: Original with a microfiber mop ahead of your polishing path for every polishing pad you intend to use until you’re finished polishing to your desired grit.

Clean the floor again with water and allow the floor to fully dry, then applying more Protec III: Original, Dual-Tech, or your preferred final coating.

After all product has fully dried, equip blue nylon pads or diamond impregnated pads then buff the surface until you achieve your desired shine.